12 English reviews written for 3DJAKE Magnetic Plate
107 customer reviews in all languages
| 5 stars | | 106 | (46%) |
|---|---|---|---|
| 4 stars | | 29 | (12%) |
| 3 stars | | 33 | (14%) |
| 2 stars | | 20 | (8%) |
| 1 Stars | | 38 | (16%) |
Filter reviews:
-
JohnV
25 November 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. -
Paul W
13 November 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. pretty rubbish quality
Rated with 1 out of 5 stars.
... save your money and get a WhamBam!
Was this rating helpful? (1) (0)
-
Will
11 September 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Mountain Range
Rated with 2 out of 5 stars.
I origionally wanted a spring steel bed for my CR10 Max but they are impossible to find in the UK so I settlet for this.
Intially I was impressed, the print surface is good.
Then I removed the sheet after a print, first impression was that it was very ungainly, way to floppy for such a large print bed, makes it difficult to remove and replace.
After removing the surface for a few prints I am now left with a print surface like a mountain range. Its basicly unusable and was a waste of money.
The magnetic bed was applied on a glass sheet and had no air bubbles, heat transfer is fine, the problem is definatley the removable surface deforming after being flexed to remove prints. Defeats the object really.Was this rating helpful? (3) (0)
-
matthew
07 August 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. mag base
Rated with 5 out of 5 stars.
brilliant, very happy, wish i got one years ago when if first came out, would of saved alot of big prints. i use abit of the spray adhesive to on the mat. double check you first layer height when first using....
Was this rating helpful? (0) (0)
-
zenxbear
04 August 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Improved dramatically the first layer
Rated with 5 out of 5 stars.
I have been struggling to get a proper first layer on the Biqu B1 SE plus. I don't know for what reason I threw money on glass bed with some mild improvement. I adapted this magnetic bed by poking holes for the screws so the plate isn't too much deformed.
This solution has been able to provide a consistent first layer.
The bed is still fragile: too much folding deformed it, and due to configuration mistake, it was dented in the middle by the nozzle pressing too hard.
The size 310x310 is a bit larger than the plate I have, so one has to place it properly in order to not hit frame.
Removing the piece is very easy with this.Was this rating helpful? (1) (0)
-
tanner hampshire u.k
03 January 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. 3DJAKE Magnetic Plate
Rated with 5 out of 5 stars.
Great quality works as well as a Creality base ordered this one as creality not available. Super swift delivery, It came well packaged but the british postal system had thrown the box about a bit and one corner of the mat was damaged. e-mailed 3D JAKE what a great customer service this company has. Sent a photo of damage new board offered but not needed but the cost has been credited to my account for future use. I wish more companys were this helpfull and customer focused.
Was this rating helpful? (4) (0)
-
Mark McQuillan
29 December 2021
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Decent enough, there is a 'but' though.
Rated with 3 out of 5 stars.
Been using one of these for around 8 months for printing PLA. Application is easy and there's a good range of sizes. Releasing parts is easy and the adhesion is great.
This is where the 'but' comes in though;
I've found that lately I've been having trouble printing smaller parts, the first layer has trouble adhering in places. I eventually found the cause is that over time the textured surface of the sheet is smoothing out as a result of use, and so the filament isn't getting any purchase on the surface and sticking. If I run my finger across the sheet, I can feel it go from rougher at the outsides to much smoother near the centre. I need to replace it now and I'm not going to use another of these as I might end up just in the same boat another 8 months from now.Was this rating helpful? (2) (0)
-
muppet
21 October 2021
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. all i got was bull shit and an empty box
Rated with 1 out of 5 stars.
first two sets i ordered some how got stuck in customs in Vienna so i was told , the second lot they said they had sent came back with an opened empty box at this point when i tried to get a hold of them again i was just ignored so i escalated my claim to PayPal in which they refunded after a week so thanks to them i got my money back to buy else where, was i glad i used PayPal any way they then contacted me wanting photo's of an empty box well L.O.L what the f.... plus they also wanted me to sign an affidavit , i think they think i stole it off myself at the age of 67 years and know criminal record ,so any body buying from 3D JAKE be very weary and try and catch the delivery driver to check the box before he leaves or what happened to me may just happen to you.
Was this rating helpful? (2) (16)
-
not a noob
21 June 2021
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. One of the best build surfaces i have had
Rated with 5 out of 5 stars.
After all but wearing out the surface of the build surface that come with my 3D printer i went on the hunt for a replacement. I wasn't overly impressed with the tempered glass build plates as either the print stuck fast or came off half way through. Did some investigating and his seemed like a cheap option as a replacement glass plate was nearly twice the price.
Adhesion is amazing and I have found that i do not need so much heat in the bed to get good adhesion. My only big mistake was cleaning the surface with acetone after printing some ABS, build surface ruined as it stripped off the coating. You live and learn, back to PVA glue on a glass bed for that in future.
The only thing i would recommend for cleaning would be Isopropyl Alcohol, i use 99% which does not seem to have any effect on the surface.Was this rating helpful? (2) (1)
-
Tom
22 May 2021
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Poor Enough
Rated with 2 out of 5 stars.
Surface too rough and not to be used with PETG. One print stuck to the brand new bed and destroyed it
Was this rating helpful? (2) (4)
Magazine Articles:
Discover 3DJake:
-
Switzerland: Free standard delivery from CHF 69.90
-
Delivery in 3 business days.
More than 10.050 products
We deliver worldwide to
more than 40 countries
Magnetic plate
Rated with 5 out of 5 stars.
I love the magnetic plate, models hold very easily and well. They can be removed fast and without problems. Maybe a little fragile to scratches and if using glue to improve object sticking, the glue can be tricky to remove and clean but I love those. .
Was this rating helpful? (0) (0)