21 questions in English for 3DJAKE Magnetic Plate

64 Questions in different languages

21 questions in English for 3DJAKE Magnetic Plate

64 Questions in different languages

Buy product

Filter questions and answers:

Hi team, I have an Elegoo Mars 4 Max; none of the plates here have the exact size as the platform. Can they safely be trimmed to size and used as normal?

This question has not been answered yet.
Can this be used to replace the bed on anycubic mega zero 2.0

1 Answer, last answered on 28 February 2023
- Andrew
  
  28 February 2023
  
  Customer Service
  
  Yes it is suitable
Hello all. Was just wondering if this build plate provides smooth bottoms or textured bottoms on prints pull off of it?

1 Answer, last answered on 28 February 2023
- Andrew
  
  28 February 2023
  
  Customer Service
  
  It would provide a light texture, not smooth.
do you have a mangnetic bed for CR-5 PRO H

1 Answer, last answered on 31 January 2023
- Andrew
  
  31 January 2023
  
  Customer Service
  
  Unfortunately not :(
When levelling printing surface on Elgoo Neptune2 with plate and magnetic base installed, rear left quadrant will not lower enough to give any nozzle clearance... help??!!

1 Answer, last answered on 19 November 2022
- douggie
  
  19 November 2022
  
  Verified purchase
  
  "Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Close this note
  
  Resetting the z-Axis has solved the problem
I have CR10 S4 & bed is a little warped (low in middle) which is why I use aluminium tape to build it up then 3mm mirror on top. Could I put this PEI sheet directly on bed & tape ?

1 Answer, last answered on 29 June 2022
- Andrew
  
  29 June 2022
  
  Customer Service
  
  Yes that shouldn't be a problem. Although, just so you know this isn't a PEI sheet.
Hi. The two worries I have is that 1) the heat from the bed won’t reach through the plate and 2) the adhesive may give off toxic fumes when heated. Any help?

1 Answer, last answered on 28 December 2021
- Andrew
  
  28 December 2021
  
  Customer Service
  
  As long as the surface is placed directly on the metal heated bed and not a glass or other surface then enough heat will get through.The surface is suitable up to temperatures of 80C, not because it gives off toxic fumes but because it just can't manage adequate adhesion at those temperatures.
Could you use this on a zortrax M300, if you bought a larger size and cut it to fit?

1 Answer, last answered on 02 November 2021
- Andrew
  
  02 November 2021
  
  Customer Service
  
  Yes but I don't think the auto-levelling would work well
Will one of these fit the new Ender 6?

1 Answer, last answered on 16 June 2021
- Andrew
  
  16 June 2021
  
  Customer Service
  
  Not an exact fit but these can be cut to size with a strong scissors - the Ender 6 has a 290x290 build plate area so you can get a larger one and cut it to size. The CR-10 version is 310x310mm so it would be the closest fit.
will I have to cut holes in magnetic plate to access screws which hold printbed to runners? Is that OK, easy, safe?

3 Answers, last answered on 14 June 2021
- Andrew
  
  14 June 2021
  
  Customer Service
  
  It is possible to do that without any issues but it is probably unnecessary as most adjustments would only need to be done via attachments beneath the bed.
- Mark
  
  14 June 2021
  
  Thanks for the reply Andrew, I have a CR10S5 with a lot of bolt heads on the heated bed so it would have to be done (or I'd never be able to remove the bed or check tightness!)
- Andrew
  
  14 June 2021
  
  Customer Service
  
  Hi Mark, it should be ok. It will be a little less supported in those areas of course but if you only make the holes as big as necessary you won't run into any problems. The bed fits the plate perfectly so you can simply measure out the places where the holes will be and I recommend using a punch or gouger to do this. The bed can be cut relatively easily but because the holes are so small, using another tool might be a bit messy.

Magazine Articles:

Discover 3DJake:

New Products:

Switzerland: Free standard delivery from CHF 69.90
Delivery in 3 business days.
More than 10.050 products
We deliver worldwide to
more than 40 countries

from CHF 69.90	free
from CHF 0.00	CHF 8.90

21 questions in English for 3DJAKE Magnetic Plate

64 Questions in different languages

21 questions in English for 3DJAKE Magnetic Plate

64 Questions in different languages

Filter questions and answers:

Hi team, I have an Elegoo Mars 4 Max; none of the plates here have the exact size as the platform. Can they safely be trimmed to size and used as normal?

Can this be used to replace the bed on anycubic mega zero 2.0

Hello all. Was just wondering if this build plate provides smooth bottoms or textured bottoms on prints pull off of it?

do you have a mangnetic bed for CR-5 PRO H

When levelling printing surface on Elgoo Neptune2 with plate and magnetic base installed, rear left quadrant will not lower enough to give any nozzle clearance... help??!!

I have CR10 S4 & bed is a little warped (low in middle) which is why I use aluminium tape to build it up then 3mm mirror on top. Could I put this PEI sheet directly on bed & tape ?

Hi. The two worries I have is that 1) the heat from the bed won’t reach through the plate and 2) the adhesive may give off toxic fumes when heated. Any help?

Could you use this on a zortrax M300, if you bought a larger size and cut it to fit?

Will one of these fit the new Ender 6?

will I have to cut holes in magnetic plate to access screws which hold printbed to runners? Is that OK, easy, safe?

Magazine Articles:

Discover 3DJake:

New Products:

We operate in a climate-conscious manner.