7 English reviews written for Fillamentum PLA Crystal Clear
17 customer reviews in all languages
| 5 stars | | 30 | (63%) |
|---|---|---|---|
| 4 stars | | 7 | (14%) |
| 3 stars | | 4 | (8%) |
| 2 stars | | 1 | (2%) |
| 1 Stars | | 5 | (10%) |
Filter reviews:
-
Luca
13 May 2023
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. -
Will Lockwood
17 November 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Fillamentum PLA Crystal Clear
Rated with 2 out of 5 stars.
I must admit to being disappointed with the colour - looked great on the spool but the print was not a Crystal clear as I had hoped and looks a bit Smokey yellow - but it print really well
Was this rating helpful? (0) (0)
-
Tobias
01 January 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Not Reliable: This Filament is Way too Brittle.
Rated with 1 out of 5 stars.
Without a doubt, the look of the material is great. Yet, as soon as you touch it, you notice how brittle it is. If you slightly bend it, it breaks.
I printed two spools of this Filament, and 50% of the prints failed because the filament blocked the printer head. In the extruder, chipped off parts of the filament got crammed into the cold end. If I tried to remove the filament, it broke off, so I had to disassemble the extruder to remove the filament bit manually which was stuck there.
The common printing temperature of 215ºC for PLA, even in the specified range for this filament, is too low for faster extrusions (fill). I usually had to increase the nozzle temperature to 225º-230ºC to get normal extrusions on fills.
If the product would be marketed as speciality Filament for art prints but explained the difficult conditions, I would give more stars. But Filamentum writes "Easy to work with at high print speeds" and
"User-friendly for both, home and office environments", which is in my opinion a lie. It requires a high amount of experience to work with this Filament.Was this rating helpful? (8) (1)
-
Alessandro
14 November 2020
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Nightmare to print with Prusa
Rated with 1 out of 5 stars.
I've had a lot of problems using this filament with my Prusa MK3S.
I've managed to print at 230, temperature below that cause the filament get stucked inside the extruder after 10 minutesduring the print.
Also, 230 works fine if your print takes less than 5 h, if takes longer you'll end up with the same problem.
I've managed to do have two successful print of 4h each, then the 3rd one the filament got stucked again around 80% of the print.
The only way to clean the extruder is by removing the nozzle and pushing another one from the topWas this rating helpful? (6) (0)
-
Jason Benham
23 July 2020
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Chichester
Rated with 5 out of 5 stars.
Excellent product, creates good quality prints with fine detail.
Was this rating helpful? (3) (0)
-
Roderick
20 May 2019
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Review written by Roderick
Rated with 5 out of 5 stars.
Excellent product
Was this rating helpful? (1) (2)
-
Martin
09 October 2018
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Review written by Martin
Rated with 5 out of 5 stars.
good
Was this rating helpful? (1) (1)
Magazine Articles:
Discover 3DJake:
-
Switzerland: Free standard delivery from CHF 69.90
-
Delivery in 3 business days.
More than 10.050 products
We deliver worldwide to
more than 40 countries
nice effect and
Rated with 3 out of 5 stars.
I'd say that PET budget filament I got on Amazon, prints far lots better than this PLA. Sovol SV06 printer. It easily cogs the printer and have mediocre adhesion. The best Fillamentum I tried so far (and the last)
Was this rating helpful? (0) (0)